How to Upgrade the RAM in a Lenovo Ideapad S510p Laptop

There are a lot of laptops out there right now, and each one is different from the last. This article is a step by step explanation of how to upgrade the RAM on your Ideapad S510p laptop. It isn't an extremely difficult task and it shouldn't take you too long to complete. Plus once you finish installing you're new RAM, your laptop will run faster.

Steps

1. 1
   Buy the right RAM cards.

   • This model comes with 6GB RAM, type DDR3L SDRAM.
   • The operating speed is 1600 Mhz.
   • The maximum RAM for this model is 16GB.
   • There are two card slots available; try to use both equally for optimal performance.
   • If you are unsure which cards to purchase, ask an employee or do more research on your model.
2. 
   2
   Prepare a work space. You will be working with small delicate parts, so create a clean work space. 2' x 2' should be plenty.

   • Get an electronics screwdriver, too (any precision screwdriver will work)
3. 
   3
   Prepare your device.

   • Power off.
   • Remove anything connected to the input ports. (Charger, USB, HDMI, etc.)
   • Remove the battery.
4. 
   4
   Remove the back panel.

   • Remove the two screws from the panel.
   • Slide the panel in a downward direction.
   • When the panel comes to a stop, pull it from the device.
5. 
   5
   Prepare to remove the original RAM cards.

   • You're working with delicate electronic parts, and you may be carrying a static charge. Remove this possibility by touching something metal.
   • The cards are held in place by a pair of clips; they are located at the edges of each card.
   • Gently slide the two clips away from the card you're removing.
6. 
   6
   Remove the original RAM cards.

   • Once clear of the clips, the card will rise away from the device at an angle. It is now loose and may be pulled away from it's holder.
   • Repeat the same steps to remove the second RAM card.
7. 
   7
   Insert the new RAM cards.

   • Do not touch the gold edge on either RAM card. These components are sensitive and may be damaged by oils on the human hand. It's a good idea to hold the cards as shown in the picture.
   • It is best to hold the card by the edges on the sides.
   • Take note of the small notch in the RAM card; this will line up with the holder.
   • Gently line up the new card and slide it into its holder. The card will be at the same angle as the original cards during their removal.
   • Carefully press the card down until it is horizontal and the clips engage, holding it in place.
   • Repeat these steps to install the second RAM card.
8. 8
   Replace the back panel.

   • Line up the panel with it's opening, offset just under it.
   • Slide the panel in an upward direction until it fully covers the opening.
   • Replace both screws that were removed at the beginning of the task.
9. 
   9
   Confirm the RAM cards are performing.

   • Power on the device.
     
   • Go to "Control Panel".
     
   • Go to "System and Security".
     
   • Go to "System".
     
   • Confirm that your system is reading the correct amount of RAM.
     
10. 10
    Troubleshoot if necessary. The parts you've been handling are sensitive, static charge or contact with the gold pins can damage them. With that in mind, there isn't much you can do if the new cards have been damaged. If you want to check them for damage, try two things:

    • First, check that both cards are fully installed. The clips can sometimes engage even when the card isn't fully in place.
    • Second, reinstall the original RAM cards. We know they worked before removing them.
    • If they work once they're reinstalled, than you know the new cards are likely damaged.
    • If they fail once they're reinstalled, there is likely a larger problem at hand. If this is the case, its best to take the matter to a professional.

      Tips

      • Use something to hold the screws once removed. (Magnet, tape, cup, etc.)
      • Keep the original RAM cards in a safe place. You or someone you know may need them some day.

      Warnings

    • For your safety, power off the device before working on it.
    • Make sure you don't zap your parts, discharge any static build up by coming in contact with something metal.
    • Do not touch the gold pins along the edge of your RAM cards. They are sensitive and can be damaged by oils on the human hand.

Location:

Share :